Sprinter T1N (years 1994 - 2006) Roof Vent Adapter

Description: Available now, Insulated Vent Fan Cover, https://www.ebay.com/itm/132946231471 Fits 14" x 14" opening. If you are ordering an Air Conditioner adapter you must call to verify position and model of AC. T1N All Rib fits where the Rib runs through the center. The One Rib would land on a flat area on one end and a center rib on other end. Sprinter Model from 1994 to 2006 Patent Pending adapter matches the contour of the OEM roof so a standard RV style vent mounts to a flat surface. Prevents distorting the roof sheet metal or vent flange and can be used as an aid for locating the fan. They are CNC machined out of UV and fire resistant expanded PVC. The fan mounts to the outside adapter. Fan adapters work with the Maxxair Deluxe series and the Fan-tastic Vent fans. The adapter fits both high and low roofs. Longer screws than came with the vent fan may be needed. The framing strips are expanded PVC and bonded to the roof with a thick bead of Windoweld. They are more flexible than wood and plenty strong to support the vent and keep it from jiggling. We double them up when installing roof top air conditioners. They are essential if the span between the OEM roof beams is more than 18". They also provide a backing for the screws that hold up the vent interior bezel. They should be placed 1/4" away from the edge of the hole so the screws for the vent go into the strips. WARNING!! Please verify the opening requirement on your Maxxair Fan. If it is 400mm x 400mm you need to purchase an adapter from our Promaster Euro Adapter listing. Please contact us if you have a Maxxair Plus. The vent adapter outside dimension is 16 3/4 X 16 3/4. If you are using a Maxxair vent our adapter fits the deluxe series, other Maxxair fan vents have a wider flange. You will need a wider adapter. Please call. The option with butyl tape includes 64" of tape. We can make adapters for offset locations. Please contact us so we can verify size and location. Roof Vent Adapter Install Tips We recommend Sikaflex 221. Locate and cut the 14 x 14 hole. You can use the adapter as a guide to mark the hole. Stay clear of roof support beams. Make a tape line 1/4" beyond the adapter perimeter. De-gloss the area with a Scotch-brite pad. No need to scuff, just dull the paint. Clean with isopropyl alcohol and let dry thoroughly. Blow dryer if it's wet and/or cold out. Apply three 1/8" beads of the Sikaflex on the face of the adapter. Then, press the adapter down onto the roof until the adhesive oozes out the sides. It's not necessary to clamp. If you do, use several lightly set clamps and spread out the clamp force over the whole surface area. Using the adhesive that oozes out, make a fillet around the adapter with a double gloved finger. Pull the tape within 15 minutes. Cure is fast on outside. Let cure overnight and then proceed with the fan install. If you purchased our Interior Framing Strips, using the hole that you cut locate where the transverse strips need to be placed on the longitudinal strips. Assemble the interior frame with the 2" screws provided. Once the frame is assembled it will be glued to the interior side of the roof using Sikaflex 221. If the strips ordered are not bay specific, then you may need to cut them to the length of the panel you are installing it in. We recommend using butyl tape for the fan install. Cover the fan flange with 1" wide tape. Place the flange onto the adapter and press down. Then drill pilot holes through the adapter and into the van roof. You may need the 4 longer screws provided for the corners. Tighten all screws very lightly against the fan flange. Some butyl will ooze out which you can trim off. Coat the fan flange, adapter and onto the roof about 1/2" with self-leveling Dicor or brush-on Flexseal. Some sealants will melt the fan plastic so you might try it on a portion of the interior bezel first. You will cut a lot of that piece off. Good idea to check the integrity and reapply the sealant every so often. **Please note, if you purchased butyl tape with this order and the butyl tape is stuck to the plastic, place it in the freezer for 15 or 20 min. It will release, then let it return to room temperature. If you have questions about this product you can call Hein at 541-49O-5O98 Please consider our other items Normal 0 false false false EN-US X-NONE X-NONE Disclaimer:Van owner and/or installer assumes all risk associated with roof top mounted items and/or components. Van owner and/or installer recognizes and agrees that this product, and each of its component parts, is sold ?as is? and that seller makes no representation or warranty of merchantability that the product is fit for any particular purpose.

Price: 79.55 USD

Location: Hood River, Oregon

End Time: 2024-08-17T04:45:13.000Z

Shipping Cost: 0 USD

Product Images

Sprinter T1N (years 1994 - 2006) Roof Vent Adapter

Item Specifics

Return shipping will be paid by: Buyer

Returns Accepted: Returns Accepted

Item must be returned within: 30 Days

Refund will be given as: Money Back

Return policy details:

Modified Item: No

Custom Bundle: No

California Prop 65 Warning: WARNING: This product contains chemicals known to the state of California to cause cancer, and birth defects or other reproductive harm. For more information: www.P65Warnings.ca.gov

Sprinter, roof, fan, adapter: NCV3 High Roof

Brand: Impact Products

Non-Domestic Product: No