Hot Wire Foam Factory Foam Fusion Nontoxic #028B-8

Description: Fast Shipping - Made in the USA - Quality Customer Service Foam Fusion 8oz Non Toxic Foam Safe Glue Styrofoam Polystyrene EPS XPS ModelingNew Hot Wire Foam Factory #028B-8 Foam Fusion Glue 8oz Size Proudly made in the USA! Includes: 8oz Bottle of Foam Fusion Glue Details: Squeeze or Brush On Non Toxic Weatherproof Solvent Free Description: Our Foam Fusion is the ultimate EPS foam glue! It permeates the foam and bonds around its cells. Other glues containing solvents will dissolve foam over time, but our formula is solvent-free. Our glue is not affected by heat or cold as with glue guns. It works with most rigid foams including Styrofoam, and many soft foams. Foam Fusion bonds foam to almost any porous surface and is easy to apply - simply squeeze or brush on. Plus, Hot Wire Foam Factory tools will cut through this glue. What customers are saying: "I tried the sample of Foam Fusion, looked at it, and thought I could substitute Elmer’s glue for it. When I did my project, I was very sorry I tried the substitution. Two weeks later, the foam pieces were falling apart with the white glue being totally wet like when I poured it. I had the HWFF people explain that Elmer’s (or plain white glue) is air dry, while Foam Fusion is a chemically drying product. I will never make that mistake again, and I wish I had the two wasted weeks back!" - Michael Kerschner, Amherst, OH MSDS available. Directions: Clean the areas to be glued. Apply a thin layer to both surfaces. Press the two pieces together. Allow to dry for 30 minutes. Full adhesion in 12 hrs. Thin layers can be cut through with hot wire tools. Cleanup: Warm water, alcohol, or acetone If you have questions we can answer for you, please don't hesitate to contact us. Our Hot Wire tools work best on rigid polystyrene foams, also known as expanded polystyrene (also known as EPS, Styrofoam or bead-board foam) and extruded polystyrene foam (also known as XEPS or XPS or insulation foam). If you are unsure whether or not this tool will cut the foam you intend to cut, please contact us before buying. The Hot Wire tools will cut many kinds of foam, but always check with the foam manufacturer to make sure there are no health or safety hazards when using hot wire tools. NOTE: Polyurethane foam (aka upholstery foam) should not be cut with hot wire tools. It needs a ton of heat, gives off toxic fumes, and leaves a lot of melted plastic wherever it is cut. We recommend that the polyurethane foams only be cut with a blade or saw.PAYMENTSHIPPINGWARRANTY/RETURNSPAYMENTSHIPPINGWARRANTY/RETURNSWe accept payment by any of the following methods: PayPal, Visa, Amex, Discover, MasterCard Buyers in California will be charged 8% sales tax. Please pay as soon as possible, as that will allow us to ship your item to you sooner! Packages are always insured. We ship within 2 business days (So if you order Monday, your order will ship by Wednesday). Weekends and holidays do not count as business days. We are not responsible for any customs fees, duties, taxes or tariffs imposed by the destination country which you may have to pay. USA - FedEx & USPS (United States Postal Service) Canada/Mexico - USPS (United States Postal Service) International Worldwide (Except Hong Kong or China) - USPS (United States Postal Service) International Limited Warranty & Limitation of Liability Information: This product is warranted for non-commercial use as follows: For 90 days from the original date of purchase, HWFF, Inc. will, at its option, repair or replace a defective unit free of charge, if the unit is defective due to an original manufacturer’s defect. This warranty covers normal use and does not cover damage which occurs in shipment or unit failure which results from alteration, accident, misuse, abuse, or neglect. Except as herein expressly set forth, HWFF, Inc. shall not under any circumstances be responsible for any direct, indirect, incidental, or consequential damage resulting from the use of the equipment. The consumer’s sole remedy shall be such repair or replacement as expressly provided above. Return Policy: HWFF, Inc. retains the exclusive and sole right as to whether an item may be returned, exchanged, or order cancelled. HWFF, Inc. thus encourages customers to use caution when placing an order, as once placed the order cannot be cancelled, nor the item returned or exchanged unless HWFF, Inc. expressly consents. In order to obtain a refund or exchange, prior approval must be given by HWFF, Inc.. Generally, HWFF, Inc. will consider returns within thirty (30) days of purchase with a 20% restocking charge. Refunds are for the cost of product only; shipping and handling charges are not refundable. Buyer is responsible for return shipping. Please ask any questions you may have prior to buying. New Hot Wire Foam Factory #028B-8 Foam Fusion Glue 8oz Size Proudly made in the USA! Includes: --- 8oz Bottle of Foam Fusion Glue Details: --- Squeeze or Brush On --- Non Toxic --- Weatherproof --- Solvent Free Description: Our Foam Fusion is the ultimate EPS foam glue! It permeates the foam and bonds around its cells. Other glues containing solvents will dissolve foam over time, but our formula is solvent-free. Our glue is not affected by heat or cold as with glue guns. It works with most rigid foams including Styrofoam, and many soft foams. Foam Fusion bonds foam to almost any porous surface and is easy to apply - simply squeeze or brush on. Plus, Hot Wire Foam Factory tools will cut through this glue. What customers are saying: "I tried the sample of Foam Fusion, looked at it, and thought I could substitute Elmer’s glue for it. When I did my project, I was very sorry I tried the substitution. Two weeks later, the foam pieces were falling apart with the white glue being totally wet like when I poured it. I had the HWFF people explain that Elmer’s (or plain white glue) is air dry, while Foam Fusion is a chemically drying product. I will never make that mistake again, and I wish I had the two wasted weeks back!" - Michael Kerschner, Amherst, OH MSDS available. Directions: Clean the areas to be glued. Apply a thin layer to both surfaces. Press the two pieces together. Allow to dry for 30 minutes. Full adhesion in 12 hrs. Thin layers can be cut through with hot wire tools. Cleanup: Warm water, alcohol, or acetone If you have questions we can answer for you, please don't hesitate to contact us. Our Hot Wire tools work best on rigid polystyrene foams, also known as expanded polystyrene (also known as EPS, Styrofoam or bead-board foam) and extruded polystyrene foam (also known as XEPS or XPS or insulation foam). If you are unsure whether or not this tool will cut the foam you intend to cut, please contact us before buying. The Hot Wire tools will cut many kinds of foam, but always check with the foam manufacturer to make sure there are no health or safety hazards when using hot wire tools. NOTE: Polyurethane foam (aka upholstery foam) should not be cut with hot wire tools. It needs a ton of heat, gives off toxic fumes, and leaves a lot of melted plastic wherever it is cut. We recommend that the polyurethane foams only be cut with a blade or saw. Fast Shipping - Made in the USA - Quality Customer Service Foam Fusion 8oz Non Toxic Foam Safe Glue Styrofoam Polystyrene EPS XPS ModelingNew Hot Wire Foam Factory #028B-8 Foam Fusion Glue 8oz Size Proudly made in the USA! Includes: 8oz Bottle of Foam Fusion Glue Details: Squeeze or Brush On Non Toxic Weatherproof Solvent Free Description: Our Foam Fusion is the ultimate EPS foam glue! It permeates the foam and bonds around its cells. Other glues containing solvents will dissolve foam over time, but our formula is solvent-free. Our glue is not affected by heat or cold as with glue guns. It works with most rigid foams including Styrofoam, and many soft foams. Foam Fusion bonds foam to almost any porous surface and is easy to apply - simply squeeze or brush on. Plus, Hot Wire Foam Factory tools will cut through this glue. What customers are saying: "I tried the sample of Foam Fusion, looked at it, and thought I could substitute Elmer’s glue for it. When I did my project, I was very sorry I tried the substitution. Two weeks later, the foam pieces were falling apart with the white glue being totally wet like when I poured it. I had the HWFF people explain that Elmer’s (or plain white glue) is air dry, while Foam Fusion is a chemically drying product. I will never make that mistake again, and I wish I had the two wasted weeks back!" - Michael Kerschner, Amherst, OH MSDS available. Directions: Clean the areas to be glued. Apply a thin layer to both surfaces. Press the two pieces together. Allow to dry for 30 minutes. Full adhesion in 12 hrs. Thin layers can be cut through with hot wire tools. Cleanup: Warm water, alcohol, or acetone If you have questions we can answer for you, please don't hesitate to contact us. Our Hot Wire tools work best on rigid polystyrene foams, also known as expanded polystyrene (also known as EPS, Styrofoam or bead-board foam) and extruded polystyrene foam (also known as XEPS or XPS or insulation foam). If you are unsure whether or not this tool will cut the foam you intend to cut, please contact us before buying. The Hot Wire tools will cut many kinds of foam, but always check with the foam manufacturer to make sure there are no health or safety hazards when using hot wire tools. NOTE: Polyurethane foam (aka upholstery foam) should not be cut with hot wire tools. It needs a ton of heat, gives off toxic fumes, and leaves a lot of melted plastic wherever it is cut. We recommend that the polyurethane foams only be cut with a blade or saw.PAYMENTWe accept payment by any of the following methods: PayPal, Visa, Amex, Discover, MasterCard Buyers in California will be charged 8% sales tax. Please pay as soon as possible, as that will allow us to ship your item to you sooner! SHIPPING Packages are always insured. We ship within 2 business days (So if you order Monday, your order will ship by Wednesday). Weekends and holidays do not count as business days. We are not responsible for any customs fees, duties, taxes or tariffs imposed by the destination country which you may have to pay. USA - FedEx & USPS (United States Postal Service) Canada/Mexico - USPS (United States Postal Service) International Worldwide (Except Hong Kong or China) - USPS (United States Postal Service) International WARRANTY/RETURNS Limited Warranty & Limitation of Liability Information: This product is warranted for non-commercial use as follows: For 90 days from the original date of purchase, HWFF, Inc. will, at its option, repair or replace a defective unit free of charge, if the unit is defective due to an original manufacturer’s defect. This warranty covers normal use and does not cover damage which occurs in shipment or unit failure which results from alteration, accident, misuse, abuse, or neglect. Except as herein expressly set forth, HWFF, Inc. shall not under any circumstances be responsible for any direct, indirect, incidental, or consequential damage resulting from the use of the equipment. The consumer’s sole remedy shall be such repair or replacement as expressly provided above. Return Policy: HWFF, Inc. retains the exclusive and sole right as to whether an item may be returned, exchanged, or order cancelled. HWFF, Inc. thus encourages customers to use caution when placing an order, as once placed the order cannot be cancelled, nor the item returned or exchanged unless HWFF, Inc. expressly consents. In order to obtain a refund or exchange, prior approval must be given by HWFF, Inc.. Generally, HWFF, Inc. will consider returns within thirty (30) days of purchase with a 20% restocking charge. Refunds are for the cost of product only; shipping and handling charges are not refundable. Buyer is responsible for return shipping. Please ask any questions you may have prior to buying. New Hot Wire Foam Factory #028B-8 Foam Fusion Glue 8oz Size Proudly made in the USA! Includes: 8oz Bottle of Foam Fusion Glue Details: Squeeze or Brush On Non Toxic Weatherproof Solvent Free Description: Our Foam Fusion is the ultimate EPS foam glue! It permeates the foam and bonds around its cells. Other glues containing solvents will dissolve foam over time, but our formula is solvent-free. Our glue is not affected by heat or cold as with glue guns. It works with most rigid foams including Styrofoam, and many soft foams. Foam Fusion bonds foam to almost any porous surface and is easy to apply - simply squeeze or brush on. Plus, Hot Wire Foam Factory tools will cut through this glue. What customers are saying: "I tried the sample of Foam Fusion, looked at it, and thought I could substitute Elmer’s glue for it. When I did my project, I was very sorry I tried the substitution. Two weeks later, the foam pieces were falling apart with the white glue being totally wet like when I poured it. I had the HWFF people explain that Elmer’s (or plain white glue) is air dry, while Foam Fusion is a chemically drying product. I will never make that mistake again, and I wish I had the two wasted weeks back!" - Michael Kerschner, Amherst, OH MSDS available. Directions: Clean the areas to be glued. Apply a thin layer to both surfaces. Press the two pieces together. Allow to dry for 30 minutes. Full adhesion in 12 hrs. Thin layers can be cut through with hot wire tools. Cleanup: Warm water, alcohol, or acetone If you have questions we can answer for you, please don't hesitate to contact us. Our Hot Wire tools work best on rigid polystyrene foams, also known as expanded polystyrene (also known as EPS, Styrofoam or bead-board foam) and extruded polystyrene foam (also known as XEPS or XPS or insulation foam). If you are unsure whether or not this tool will cut the foam you intend to cut, please contact us before buying. The Hot Wire tools will cut many kinds of foam, but always check with the foam manufacturer to make sure there are no health or safety hazards when using hot wire tools. NOTE: Polyurethane foam (aka upholstery foam) should not be cut with hot wire tools. It needs a ton of heat, gives off toxic fumes, and leaves a lot of melted plastic wherever it is cut. We recommend that the polyurethane foams only be cut with a blade or saw.

Price: 9.95 USD

Location: Lompoc, California

End Time: 2024-08-12T21:37:17.000Z

Shipping Cost: 0 USD